Nylon Stringing Troubleshooting
Nylon stringing occurs when molten plastic escapes during travel moves, leaving hairs or thicker strands between printed features. Moisture often contributes, but temperature, retraction, travel paths, and nozzle condition can produce similar symptoms. This AValidReview guide starts with material preparation before changing slicer settings. Work through the steps in order, make only one change at a time, and document the results. All numerical adjustments below are approximate starting points. The filament datasheet and the printer's limits take precedence.
1. Identify defects and check printer compatibility
First, distinguish strings from other defects. Fine hairs spanning empty space usually indicate travel ooze. Thick branches attached to seams can involve restart pressure or accumulated material. Blobs, rough surfaces, and intermittent extrusion suggest moisture or a flow problem worth investigating before retraction.
Confirm that your nozzle, bed, and filament path, and the hotend are compatible with your nylon. Do not exceed any component’s temperature rating, especially on printers with PTFE-lined hotends. Filled nylons may require an abrasion-resistant nozzle; follow the filament manufacturer's recommendation.
Third, arrange ventilation appropriate for the material and keep the printer away from occupied sleeping areas. An enclosure helps temperature stability but does not replace ventilation. Avoid electronics overheating, drafts across the print, and follow the printer maker’s enclosure limits.
2. Dry the nylon before tuning settings
First, treat unknown storage history as a reason to check drying requirements. Nylon absorbs airborne moisture, including after a package is opened. Noise (popping, hissing) may be present although wet filament can also print without obvious noise. Look for irregular extrusion, inconsistent extrusion, bubbles, rough surface finish, and other printing irregularities.
To dry the spool, follow the filament manufacturer’s temperature and duration instructions. Because different formulations of nylon exist, different treatment is also required. Use the equipment rated for the required temperature and check the spool’s heat tolerance. A dryer intended mainly for lower-temperature materials may be inadequate. Avoid shared food ovens and uncontrolled heating methods.
Third, repeat a small print after drying. Less bubbling and fewer strings suggest moisture was contributing. Drying is a preparation step, not a guarantee of string-free printing. If improvement is incomplete, verify actual drying temperature, duration, and moisture removal rather than immediately increasing retraction.
3. Keep filament dry throughout the print
First, feed dried nylon from a suitable dry box or active dryer when practical, particularly during long prints or in humid rooms. Keep the path to the extruder short and protected without introducing sharp bends or excessive drag. Follow the dryer’s instructions for venting and continuous operation.
Second, keep unused filament in a sealed container with maintained desiccant. While desiccant can help preserve dryness, it’s a poor substitute for drying a moist spool. A low container-humidity reading does not prove that the filament’s interior is dry.
Third, consider the formulation. Polymaker’s Fiberon PA612-CF15 is described in their catalog as a strong, low-moisture material for functional prints, so it’s a relevant example when looking at nylons. This doesn’t mean it’s moisture-proof or stringing-proof. It’s recommended to use their prep instructions, as opposed to transferring assumptions to this filament from another nylon.
4. Establish a Controlled Test and Tune Temperature
Save your current profile and print a small two-post stringing test. Make sure you’re using dry filament and set the profile to use the same settings for layer height, print speed, cooling, flow, and travel. Record the settings for comparisons to be meaningful.
Start within the recommended nozzle temperature range by the manufacturer. If extrusion is consistent but strings remain, lower temperature by approximately 5°C per test while staying within that range. Verify the printer actually applies each intended temperature if a temperature tower is used.
Third, inspect more than the hairs. Lower temperature can reduce ooze while weakening layer bonding or causing underextrusion. Also reject settings that cause gaps, poor adhesion, or extruder skipping. The useful endpoint is a clean-enough print with dependable extrusion, not the lowest temperature that produces an attractive test.
5. Adjust retraction cautiously
First, use the printer or hotend maker’s nylon retraction profile as your baseline. Direct-drive and Bowden systems behave differently, so copied distances may be unsuitable. Once again, travel moves in the slicer preview must be enabled for retraction.
Second, change distance alone in small increments. Approximately 0.2 mm steps for direct drive or 0.5 mm steps for Bowden can be useful starting increments, subject to hardware limits. Retracting too much can pull softened material into cooler regions, encourage jams, or leave gaps after travel.
Keep the best distance constant before adjusting retraction speed modestly. Faster is not automatically better: slipping, clicking, or chewed filament indicates trouble. Compare strings and restart quality together. Avoid adding extra restart material to hide gaps until excessive retraction and restricted extrusion have been ruled out.
6. Reduce opportunities for travel ooze
First, inspect the preview for long open-air moves. Options that avoid crossing outer walls or keep travel within printed regions may hide or reduce visible strings, but detours can increase travel time. Compare actual paths rather than enabling every travel option.
Second, consider a modest increase in travel speed. The increase should be constrained by the mechanical limits of the printer. This reduces time available for ooze, but short moves may never reach the requested speed. Leave acceleration conservative unless you understand the machine’s limits.
Third, test wipe separately if your slicer supports it. Keep Z-hop only as large as needed for clearance, as extra lift adds time during which ooze can occur. Do not turn off clearance protection if the nozzle is striking part features. Avoid using maximum part cooling as a shortcut: nylon may lose layer bonding or warp.
7. Inspect hardware and validate the final profile.
1. Check for nozzle buildup and heater block leaks, inconsistent extrusion, and filament-path resistance. Follow the printer’s maintenance procedure. Keep hands and tools away from energized wiring and moving parts. Never touch a hot nozzle or improvise disassembly of hotend.
2. Inspect nozzle wear with filled nylons. SUNLU PA6-CF20 is a catalog example of a filled nylon for high-strength and heat-resistant parts with specific user requirements. Its inclusion does not establish better stringing performance. Verify its nozzle and processing requirements before treating a generic nylon profile as suitable.
Third, print a representative part after the small test passes. Longer travel moves and longer exposure to humidity can reveal remaining problems. Save the successful profile under the exact material and nozzle combination. For residual hairs, prefer careful mechanical trimming after cooling; avoid open flames and uncontrolled heating.
Product reviews for this guide
- Polymaker Fiberon PA612-CF15 Carbon Fiber Nylon Filament 1.75mm, Black, 0.5kg — full review
- SUNLU Official Filament Connector, Fast Heating Filament Splicer for 3D Printer Filament 1.75mm, Up to 240°C, Compatible with PLA PETG TPU ABS PA Nylon, Easy to Use, Pack with 200PCS PTFE Sleeve — full review
- SUNLU PA6-CF20 Carbon Fiber Nylon 3D Printing Filament 1.75mm, 1KG, Black — full review
Frequently asked questions
Should I dry a newly opened nylon spool?
Read the material manufacturer’s instructions. Sealed spools do not necessarily mean it is print-ready dry. Extrude a test filament, if it shows signs of moisture, then it is recommended to dry the spool before continuing.
Why does nylon still string after drying?
It’s possible that the drying process was not complete. Check your drying process and change one printing variable at a time.
Can I eliminate stringing with more retraction?
Not reliably. Excessive retraction can cause jams and restart gaps without solving moisture-related ooze. Dry first, establish temperature, and adjust retraction cautiously.
Does carbon-fiber nylon avoid stringing?
No formulation guarantees that. Filled nylons still require appropriate moisture control and settings, and their hardware requirements can differ from unfilled nylon.
Should I increase cooling to stop nylon hairs?
Within the material’s recommendations. Additional cooling may help particular features but can compromise layer adhesion or increase warping. Address drying and travel ooze first.
When should I stop tuning?
Stop tuning when consistent, representative parts are produced. Parts should adequately bond. Hairs are better than gaps, so don’t worry too much about hairs.
Next: pick a printer
Once you have a CAD tool, the other half of the equation is the printer itself. Browse our owner-grounded reviews to find one that matches your budget and skill level.
